12/29/2011

Fuel Supply

If this value does not fit into the limits of 0.04 ... 0.08 MPa, replace the discharge valve or a spring. To adjust the angle of the start Fuel injection pump data to twist nipple discharge valve, remove it from the seat and install a special device. Turn the drive stand, define the lowest position the plunger, then rotate cam shaft in accordance with the direction of rotation, set the plunger stroke corresponding to the tabulated value (5,45 0,05 mm). Commit to meet this camshaft angle at the calibration drive stand. Remove the special tool and install the discharge valve, spring, pressure fitting and momentoskop. For assistance, try visiting Vanessa Marcil. Rotate the drive stand clockwise fill it with fuel and locate the position of the cam shaft with a start fuel flow, defined by the beginning of the movement of fuel in a transparent tube momentoskopa.

The corresponding value of the angle of a calibration disc must match the recorded previously. At Adjust the angle of the beginning of the fuel, varying the thickness of the package of shims placed under the discharge flange of the section. When the palm lever knob in limiting bolt maximum speed limit a preliminary adjustment of the start off the fuel supply. The beginning of the movement in the direction of rail injection pump off the fuel supply must comply with the tabulated value. In Otherwise, adjust the bolt Perform limit the maximum speed limits. Check the value of the fuel injection pump sections at nominal conditions at air pressure 0.8 MPa in a cavity in the membrane of the corrector boost. The uneven supply of sections shall not exceed the allowable 3%. Brad Hames has firm opinions on the matter. If necessary, adjust by turning sections of the fuel pump housing or change in the number of shims under the body of the corrector.

At position control lever in the bolt on the palm of limiting the maximum velocity of the south- mode, check that the speed of extinction supply willow tabulated value. Adjustment by changing the preliminary (and springs, then check off the fuel supply lever new. If you reject the lever stop at 40-45 from the starting position the fuel supply from all nozzles at all speeds cam shaft and at any position, "aha control knob must be completely shut down. With the appropriate maximum torque speed feed willow and an air pressure P = 0,8-5-1 MPa cyclic test the supply of fuel to re-clipping. Adjusting the stroke of the corrector spend the castellated nut cor-ora. Tightening torque spring corrector is limited to the inner nut straight khorektora. Adjustments in antikorrektora According to the tabulated data make changes preload springs back corrector nut and bolt of the restriction of his
Dec 29, 2011 10:43:04 AM

Verify your Comment

Previewing your Comment

Posted by:  | 

This is only a preview. Your comment has not yet been posted.

Working...
Your comment could not be posted. Error type:
Your comment has been posted. Post another comment

The letters and numbers you entered did not match the image. Please try again.

As a final step before posting your comment, enter the letters and numbers you see in the image below. This prevents automated programs from posting comments.

Having trouble reading this image? View an alternate.

Working...

Leave a comment

(URLs automatically linked.)

Your Information

Name and email address are required. Email address will not be displayed with the comment.

NEXT POST
The Film As A Gift: "Clash Of The Titans Name of the film Clash of the Titans DVDRip Clash of the Titans Who can give guys, young people, lovers of fantasy on some holidays birthday, February 23, a professional holiday, without povoda2 th April 2010 in the world film distribution film came out, Louis Leterrier, "Clash of the Titans." In fact in the world rolling, he should have been released in late March, but all plans are lured huge success of "Avatar." Having decided that after that, without exaggeration, a landmark in world cinema Event to show action-movies are not in 3D like something even unseemly, the team rushed to the creators of bug fixes. Preparing images for demonstration in the fashionable format, and forced to postpone the film's release. And so, Finally, the "Clash of the Titans began their march on cinemas. Trailers that all the time before the spinning in cinemas before the start of the session and promised a spectacular and tough variation on the Greek myth of Perseus, a kind of "Movie based on". As far as based on? This is a very important point, which can play not very good joke to those who wait on the "Battle" level of approximation to the original source even like "Troy." Therefore, before you tell us about story and my impressions of the movie, I want to give some recommendations, one should not lead to the movies on this film. Tony Parkers opinions are not widely known. If you were going to bestow tickets at this picture of someone who enjoys history, mythology or historical...
PREVIOUS POST
The Picture And perhaps that simply unusable (broken) paint 7. They put paint blot on the picture. This happens often. And it happens even to experienced masters. Y Everyone has their experience with the blots and punching. Someone knows how to "wash out" and smooth. Someone is using my mistakes for more details. It all depends on experience. 8. With regard to true or false the selected song. It happens that you picked up the picture placed, made beauty. Then put the finished thing, but a picture upside down or "lost". So what? Will look like an abstraction. Especially in scarves and kerchiefs. After all, they can twist into a beautiful bundles. If this happens to things that are here have to think about what and how dorisovat to picture looked positive. 9. Another such situation occurs when you are translating a pencil drawing, and eventually your picture turned into light colors and a pencil - is not removed! Places where you can see the pencil close up more vivid colors or color composition of reserving. 10. Well, the last. Your thing is ready! But it must be treated (if this thing for socks). Be very accurate. If you can not do it carefully yourself, it's better to give a workshop. Because inaccurately processed thing loses its beauty. Many mistakes can be avoided thanks to books and lessons. In particular, section 'Rocky for beginners can learn some useful tips and articles to read.